Thursday, May 29, 2014

Wiring up Dad's BAR 18 - Memorial Day - 5-26-14

As the work on BAR 62 starts to get more sporadic - Dad's car, BAR 18, has become the focus of some more work. Today, the chore was wiring up the ignition system. 
My initial reaction was to strip the wiring completely and start fresh, however the existing wiring was found to be relatively new, in good condition and usable. One thing neither Dad nor I liked was the location of the battery - near the fuel tank - making it very difficult to charge without removing it and very difficult to remove. We relocated the battery and the flat mount buzz coil I've mentioned earlier to a battery box mounted on the operator's side near the windscreen. This time, due to space, the battery box was mounted parallel to the car, unlike the 62. 
Here the box is mounted and the wiring is pretty much done - for the ignition at least.

Here is the previously installed cutoff switch, which I was able to reuse - note the newly installed toggle switch near it - this will be for the Head / tail lights. 

Here is the original ignition cutoff switch - still mounted - and re-used.

In addition to the conversion to a completely 12 volt system, I eliminated the positive ground on the timer and coil and ran a negative ground setup. Works fine as the coil buzzed as it should!
 More to come!

Monday, May 19, 2014

Progress and problems - 5-18-14

After the recent successful startup of the 62, and starting work on the 18, I figured my 'oh what the heck I'll fire the 62 up and give it another test run' wouldn't take too long. 
Best laid plans....
We swapped spark plugs and eventually got the car started.
I took the advice of someone on the RailroadMotorcarMaintenance group and jacked up the rear of the car to allow the belt to be tightened and the rear wheels to spin freely. It was during this that we noticed a problem - the crank side wheel is wobbling badly when it turns. We'll be addressing this soon. We suspect the axle has a tweak in it. 
On another note, this represents the first time that the 62 and 18 have been photographed together. 
After the test run, we tied up some more wiring, removed some old wiring clips that were in the way and generally made it more tidy. 


After the test run - both went back into the garage as we wait for future work..

More to come!

Sunday, May 18, 2014

The little details left - 5-14-14

With any project - there are little details to get it completed, this is one of them
Dad ordered some replacement air filters - K&N brand - so I can honestly say that my motorcar is K&N Equipped :-) With the top and bottom altered slightly to be compatible with the element - they are all installed. Thanks Dad!

More to come!

Saturday, May 17, 2014

In celebration of getting the #62 running..... 5-12-14

Literally minutes after we got the 62 fired up - I was helping Dad pull the roof of BAR 18, his M14 motorcar. 
Here is the 18 after the roof removal.

The next day, Dad had replaced the rivets that were missing from the roof

While giving the roof a once over, Dad found this written in pencil inside the roof. BAR X3403. 
Dad posted this picture on the Bangor and Aroostook Railroad Facebook Group. In response to this, group members Larry Curtis and Warren Cain put together that the BAR X3403 being a ballast car indicated that this car, BAR 18 was most likely the speeder assigned to the ballast gang. 

More come!

Friday, May 16, 2014

The Culmination of 5 months of effort! - 5-11-14

This was the day that it all came together. After months of effort - the 62 was rolled outside in one piece for the first time in a LONG while. The video says it all:

More to come!


Thursday, May 15, 2014

Hitches mounted and painted - 5-10-14

With his usual speed and quality....
Dad has gotten the primed rear hitch painted and mounted

Here is the front - It might look off center, but it is centered on the frame, not the engine. \

More to come!

Sunday, May 11, 2014

Getting Hitched Up - 5-9-14

Dad's skills extend far further than the paint and body work that this project has focused on. 
These are the two hitches Dad has designed, cut, drilled and had welded

This is the other side of the front hitch

And here they are both primed.

More to come!